Exactly How to Remove as Well as Replace a Bath Tub
Exactly How to Remove as Well as Replace a Bath Tub
Blog Article
This post following next involving A Step-by-Step Guide to Installing a Bathtub is fairly motivating. You should look it over.
Installing a bath tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily available, the job can move immediately; if you need to open up a wall to get rid of the old bathtub and position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old tub and also embeded in the brand-new one. Make certain you have qualified yourself for the work and also are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed job, it is far better to think about using one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will help you install a new bathtub in your shower room if you have actually currently acquired a new bathtub and also do not need to alter the arrangement of your previous water supply pipelines.
Your devices as well as product checklist need to make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to stop stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be rather bothersome due to the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipes. When the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Before going on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the tub in the called for setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bathtub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water as well as examine all joints as well as brand-new pipework for leaks and tighten them if essential. Load the tub and also inspect the overflow outlet and the regular outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bathtub has actually been utilized at least once as this will resolve it into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in place in between the faucet and also the sink. Secure the faucet in position with the manufacturer given backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall between the bathroom and the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water before sealing, to enable the movement experienced when the tub is in use. The sealant can split rather very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were brought to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on another web property. Do you know someone else who is curious about the topic? Feel free to share it. Thanks so much for going through it.
Visit
Report this page